PORSCHE 924 S TURBO HATCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2005-08 - Engine (includes uncategorized and accessory items) BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,816.00
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection 10606 An interesting fact: did you know the factory thermostat doesn't start to even open until 186.8f and doesn't fully open until almost 210f? did you also know that the new '09 dfi engines run a 176f thermostat? Or how about factory turbo, GT2, and GT3 engines that run with even colder thermostats from the factory? This low temperature thermostat, featuring a calibrated, German-made 160f thermostat pre-installed in a new, oe wahler thermostat housing and gasket, is calibrated to allow thermostat opening a full 20-25f degrees earlier than the factory thermostat. That means that the the low temperature thermostat is designed to be fully open by 180-185f, allowing for full flow to the cooling system to maximize c...(choose a part on the right to read more) General FitmentBOXSTER 1997-04BOXSTER 2005-08 911 1998-05 911 2005-08 CAYMAN 2006-08
$109.99
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,921.60
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection 22011099702 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. General Fitment911 2005-08911 1998-05
From $1,307.90
Make a selection AP9972TT110 Continuing on our modification path for the Porsche 997.2 turbo, agency power has just finished and released their new carbon fiber cold air intake kit. the carbon fiber airbox is a direct replacement for the OEM intake box. the airbox is made using a prepreg process which allows the entire airbox to be flawless from pulls. similar in shape to the OEM box for fitment, this carbon fiber unit features enlarged holes to fit dual K&N cone air filters. the 2x2 weave is finished in a gloss clear coat and sits nicely where the standard plastic box once was. These filters are pressed in through the rear of the intake box utilizing the rubber seal on the filter as a secure fit. General Fitment911 2005-08
$1,500.95
Make a selection AP9972TT170 The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.
$3,749.95
Make a selection BBI9978200001 The bbi autosport Porsche 996 & 997 streetcup roll bar features a 2-piece design and 4130 chrome moly steel tubing (1.5" x .120" main hoop & 1.5" x 0.95" rear hoops) for excellent strength to weight ratio. Taking a sensible design approach, the 2-piece construction allows the bar to be mounted to the front seat belt mounts and to the rear strut towers (stronger mounting points), and still be compatible with the factory bose subwoofers. Other similar roll bars on the market are not compatible with the subwoofer. For superior strength and rigidity, the bar utilizes "x" braces on both front and rear sections and each joint has been meticulously tig welded by hand. Bolt-in installation is accomplished by usin...(choose a part on the right to read more)
$2,395.00
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection FVD99710003 Kit includes: General Fitment911 2005-08
$9,896.70
Make a selection FVD99710011 Kit includes: General Fitment911 2005-08
$1,206.70
Make a selection FVD99110042SK +140 crank hp & +155 crank tq gain on the turbo and +100 crank hp & +126 crank tq gain on the turbo s. All while offering ultra-smooth drivability and reliability that you expect from your Porsche. Package includes: - FVD my genius handheld flash tool (included). - FVD tuning software FVD99161840mg. - bmc sport filter 47079801. - FVD sound version valved muffler with 200 cell hjs tri-metallic cats bes99120240skhd. - valve control module with remote control beskls001001. - FVD headers bes99101040s. - FVD exhaust installation kit (everything needed for simple installation). FVD software power gains: max. Power - 485 kw (660 hp) @ 6500rpm max. Torque - 870 nm (642 lb.-ft.) @ 3750rpm max. Speed - 330km/h (206 mph) ...(choose a part on the right to read more)
$13,662.51
Make a selection AP997TT174 As the horsepower on your 997 turbo increases, so does the need for preventative products to ensure your boost is holding strong. The stock boost hoses are much like a rubber brake line that expands outwards under pressure. This causes a loss in boost pressure and can sometimes relate to the hose blowing off the turbo or y-pipe leaving you stranded. Because the agency power silicone boost hoses are made from 4ply silicone with cnc machined 6061 aluminum ends, they will never pop off. The property of the silicone also keeps it at a fixed circumference as the silicone will not expand. General Fitment911 2005-08
$699.95
Make a selection AP997TT155 Agency power has developed these OEM boost recirculation valves (brvs) for the Porsche 997 turbo vtg turbochargers. like on the older 996tt, the stock valves use a rubber diaphram which will leak boost on the higher rpm. this part also deteriorates over time leading to boost failure. the new agency power brv uses a piston and spring design like our other popular diverter and blow off valves we have been producing since 2005. this design holds boost pressure all the way to redline and with the vtg design, helps boost come in stronger. the 997 vtg turbos have the valve mounted directly on to the turbocharger. to add this enhancement on the 997 turbo, agency power had to engineer a product that would be a fu...(choose a part on the right to read more) General Fitment911 2005-08
$275.95
Make a selection BBI9963010001 The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.
$1,330.00
Make a selection 220110997061 More air = more power! The incredible 997.2 Porsche turbo received a completely redesigned engine with many substantial upgrades. This latest turbo is the most powerful, revolutionary and capable Porsche turbo to ever come out of stuttgart. The 997.2 Porsche turbo may have been labeled a facelift but the engine is another major evolutionary leap forward in Porsche's coveted turbo history. This 7th generation turbo engine, titled the 9a1, delivers 500 hp (530 hp in s models) and once again, raises the performance bar in the sports car world. The new 997.2 ipd turbo plenum was considerably more difficult to design and develop than previous plenums. The good news is that all these efforts have yielded a much easi...(choose a part on the right to read more)
$1,094.50
Make a selection 22011099601 More air = more power! Ipd plenum's patented, cast aluminum "y" style plenum increases horsepower and torque by optimizing airflow into the intake manifold. The factory plastic "t" style intake creates airflow turbulence, which deprives the motor of air, robbing hp and torque. Ipds "y" style plenum smoothly channels the airflow towards the left and right cylinder banks. The engine receives a larger mass of air at a higher velocity, which equates to increases in hp and torque across the entire rev range. The end result is improved acceleration and increased boost response (on turbo vehicles). Ipd plenum's provide dyno proven results and are a simple and cost effective way to increase power. Want more pow...(choose a part on the right to read more) General Fitment911 2005-08911 1998-05
From $903.10
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,390.40
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FSPOR992TVLV Treat your 992 turbo to the finest cat-back exhaust solution on the market. This valveed exhaust system is plug-and-play with the factory pse system so you can turn pse off for quiet highway cruising and turn pse on for ripping twin turbo sports car sound!
$5,245.95
Make a selection FVD11104001 These headers are meant to replace the original 993 GT2 r (993 111 039 83) headers that are no longer available. They will reduce turbo lag and add horsepower and torque. Made of t316 stainless. Primaries are 42mm (1.65 ). Merge into a 50mm (2 ) motorsports collector. Manufactured by m&m exhaust in Germany.
$1,835.90
Make a selection FVD11103901 These headers are meant to replace the original 993 GT2 r (993 111 039 83) headers that are no longer available. They will reduce turbo lag and add horsepower and torque. Made of t316 stainless. Primaries are 42mm (1.65 ). Merge into a 50mm (2 ) motorsports collector. Manufactured by m&m exhaust in Germany.
$1,835.90
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |